Welds & Joinery, Up Close

Anyone can make steel look good from across the yard. This is what our work looks like up close: the welds, corners, gussets and joints that hold it all together.

How we join steel

Welded right around

Where a joint carries load, it gets welded all the way around. Tack welds are for holding parts in place, not for holding the job together.

Ground where you can see it

Gate corners, sign frames and furniture get ground and blended so the joint almost disappears. Hidden structural welds are left full strength.

Gussets where the weight goes

Legs, lifting lugs and mounting points get gussets and doubler plates, so the load spreads into the steel instead of tearing at one weld.

Clean steel under the finish

Spatter off, edges broken and the steel prepped before it goes for galvanising or powder coat. A good finish starts with clean steel.

Close-ups

Stack of dimes (TIG · 304 stainless): An even TIG bead on a stainless bench frame corner, with the heat tint left as it came off the torch. Steel Workbenches & Welding Benches
Leg to base plate (MIG · 75 SHS + 6 mm plate): A full fillet weld right around the leg, plus a gusset, so the bench doesn't rack when you're flogging it. Steel Workbenches & Welding Benches
25 mm platen top (Multi-pass fillet · machined plate): The heavy leg joins the thick top with a multi-pass weld. The 28 mm hole grid takes standard clamps and fixtures. Steel Workbenches & Welding Benches
Mitred and ground flush (RHS gate frame · ready for galv): A 45° corner welded right around and ground back so the joint line almost disappears before the gate is galvanised. Gates, Fencing & Balustrades
Bollard base plate (168 pipe · 12 mm plate · 4 gussets): Four gussets carry the load from the post into a thick base plate, then the whole lot is hot-dip galvanised. Gates, Fencing & Balustrades
Rolled plate seam (Butt weld · 12 mm plate): Multi-pass seam on a rolled fire pit wall. Thick plate and a full weld mean it won't split or warp after years of fires. Fire Pits & BBQs
Footrest ring (Rolled flat bar · fully welded): The footrest ring is rolled and welded to every leg, so it takes a boot on it every night without working loose. Fire Pits & BBQs
Under the tray (Crossmembers · chassis mounts): Crossmembers fully welded into the main rails and bolted to the chassis with high-tensile bolts. This is the part that takes the corrugations. Ute Trays, Canopies & 4WD
Headboard and ladder rack (SHS frame · black powder coat): Every upright welded to the frame and blended before powder coat, so the headboard stays tight with a load strapped to it. Ute Trays, Canopies & 4WD
Lifting lug (Lug + doubler · multi-pass fillet): A doubler plate under the lug spreads the lift into the bin wall, and the multi-pass weld runs right around it. Workshop Cabinets, Shelving, Bins & Crates
Cage corner and stacking foot (50 × 50 mesh · angle frame): Mesh welded at every crossing and a stacking foot on each corner post, so loaded cages sit square on top of each other. Workshop Cabinets, Shelving, Bins & Crates
Cabinet corner (Folded sheet · stitch welded): Folded panels stitch-welded inside and ground clean outside, with a full-length hinge and welded shelf brackets. Workshop Cabinets, Shelving, Bins & Crates
Cut-through Corten (Corten · laser cut · LED backlit): Crisp cut edges in the Corten skin, with the frame behind welded and blended so the light comes through clean. Signature Series: Plasma-Cut & Corten
Planter corner (Corten · welded and blended): Corten planter corners welded and blended into one clean edge, then left to weather into a deep rust. Signature Series: Plasma-Cut & Corten

Service area: Australia-wide